Miller Electric ST 44 Series Wire Feeder Instrukcja Właściciela

ProcessesDescriptionMIG (GMAW) WeldingFlux Cored (FCAW) WeldingWire FeederOM-216 655G 2009−06Effective with serial number: 250 950ST 44 Series Wire Fe

OM-216 655 Page 62-3. WEEE Symbol (For Products Sold Within The EU)Do not discard this product withgeneral waste.Reuse or recycle Waste Electricaland

OM-216 655 Page 7SECTION 3 − INSTALLATION3-1. Serial Number And Rating Label LocationThe serial number and rating information for this product is loca

OM-216 655 Page 83-5. 14-Pin Plug InformationPin* Pin InformationAJBKICLNHDMGEFA 24 volts AC with respect to pin G.B Contact closure to A completes 24

OM-216 655 Page 91 Inlet Wire Guide2 Intermediate Wire GuideInstall and secure inlet wire guide,and intermediate wire guide.3 Drive Roll (4)Install dr

OM-216 655 Page 10SECTION 4 − OPERATION17114-1. ST 44 Series Panel Controls1 Voltage Control2 Purge Control3 Jog4 2T−4T Switch5 Power ON-OFF6 Digital

OM-216 655 Page 114-2. Run-In Control and Burnback Control246810246810 tRun-In ControlUse control to set wire feed speedbefore arc initiationAfter arc

OM-216 655 Page 12SECTION 5 − MAINTENANCE & TROUBLESHOOTING5-1. Routine Maintenance! Disconnect power before maintaining.3 MonthsReplaceUnreadable

OM-216 655 Page 135-2. TroubleshootingProblem SolutionUnit is completely inoperative. Check continuity of Power switch S1, and replace if necessary.Re

OM-216 655 Page 14NotesWork like a Pro!Pros weld and cutsafely. Read thesafety rules atthe beginningof this manual.

OM-216 655 Page 15SECTION 6 − ELECTRICAL DIAGRAM956.142.484

Thank you and congratulations on choosing Miller. Now you can get thejob done and get it done right. We know you don’t have time to do it anyother way

OM-216 655 Page 16SECTION 7 − PARTS LIST. Hardware is common andnot available unless listedFigure 7-1. ST 44 Complete Assembly (Optional Equipment Sho

OM-216 655 Page 17DescriptionPartNo.Dia.Mkgs.ItemNo.Figure 7−1. ST 44 Complete AssemblyQty Basic Digital Ultra−Lite1 000058427 Ring 1 1 1. .

OM-216 655 Page 18. Hardware is common andnot available unless listedFigure 7-2. 4 Roll Wire Drive Assembly (All Models)May 2009DescriptionPartNo.Dia.

OM-216 655 Page 19Table 7-1. Drive Roll And Wire Guide Kits (4 Drive Roll). Base selection of drive rolls upon the following recommended usages:1. V-

Notes

Notes

Notes

milan_warr 2009−05Effective January 1, 2009This limited warranty supersedes all previous Miller warranties and is exclusive with no otherguarantees or

ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2009 Miller Electric Mfg. Co. 2009−01ITW Welding Products Italy S.r.l.Via Privata Iseo, 6/E20098 San Giuliano

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol

DECLARATION OF CONFORMITYfor European Community (CE marked) products.ITW Welding Products Italy S.r.l. Via Privata Iseo 6/E, 20098 San Giuliano M.se,

OM-216 655 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _2007−047Protect yourself and others from injury — read and follow these precau

OM-216 655 Page 2Welding produces fumes and gases. Breathingthese fumes and gases can be hazardous to yourhealth.FUMES AND GASES can be hazardous.D Ke

OM-216 655 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over,

OM-216 655 Page 41-4. California Proposition 65 WarningsWelding or cutting equipment produces fumes or gaseswhich contain chemicals known to the State

OM-216 655 Page 5SECTION 2 − DEFINITIONS1 1.1 1.2 1.33 3.1 3.2 3.34 4.1+22.12.2++56+2.3S-178 936A. Warning! Watch Out! There are possiblehazards as sh